蘭鵬檢視原始碼討論檢視歷史
|
蘭鵬,男,2015年1月博士畢業於北京科技大學鋼鐵冶金系,北京科技大學科技大學冶金與生態工程學院副教授。
人物簡歷
獲得北京科技大學第十屆研究生十佳學術之星,隨後留校做師資博士後。2015年7月至2016年7月於浦項工科大學開展博後工作,2017年6月聘為北京科技大學鋼鐵冶金系講師。已發表論文30餘篇,其中第一作者的SCI/EI檢索論文近20篇,是Metallurgical and Materials Transaction A、Journal of Alloy and Compounds, Materials Characterization, Steel Research International等國際期刊的通訊審稿人。
本科課程
科研方向
鋼的凝固理論與應用
高品質鋼連鑄工藝與技術
大型鍛造鋼錠凝固質量控制
先進高強高韌汽車鋼設計與開發
學術成果
論著
1. Lan P, Nguyen D A, Lee S Y, et al. Heat transfer and solidification microstructure evolution of continuously cast steel by non-steady physical simulation[J]. Metals and Materials International, 2017, 23(3): 568.
2. Lan P, Zhang J. Twinning and Dynamic Strain Aging Behavior during Tensile Deformation of Fe-Mn-C TWIP Steel[J]. Materials Science and Engineering: A, 2017.
3. Lan P, Tang H, Zhang J. Hot ductility of high alloy Fe–Mn–C austenite TWIP steel[J]. Materials Science and Engineering: A, 2016, 660: 127.
4. Lan P, Tang H, Zhang J. Solidification Microstructure, Segregation, and Shrinkage of Fe-Mn-C Twinning-Induced Plasticity Steel by Simulation and Experiment[J]. Metallurgical and Materials Transactions A, 2016, 47(6): 2964.
5. Lan P, Zhang J. Thermophysical properties and solidification defects of Fe–22Mn–0.7 C TWIP steel[J]. steel research international, 2016, 87(2): 250.
6. Lan P, Zhang J. Study on the mechanical behaviors of grey iron mould by simulation and experiment[J]. Materials & Design, 2014, 53: 822.
7. Lan P, Zhang J. Strength, microstructure and chemistry of ingot mould grey iron after different cycles of low frequency high temperature loads[J]. Materials & Design, 2014, 54: 112.
8. Lan P, Zhang J. Analysis of Solidification Microstructure and Hot Ductility of Fe-Mn-C TWIP Steel[J]. Mater Sci Technol, 2014, 30(11):1297.
9. Lan P, Zhang J. Numerical Analysis of Macrosegregation and Shrinkage Porosity in Large Ingot[J]. Ironmak Steelmak, 2014, 41(8):598.
10. Lan P, Zhang J. Effect of Mould taper and Wall Thickness on Steel Ingots Soundness by 3-D Solidification Simulation[C]. The Minerals,Metals & Materials Society 2012.
11. 蘭鵬, 唐海燕, 紀元, 等. Fe-22Mn-0.7C TWIP 鋼的熱塑性與斷裂機制[J]. 工程科學學報, 2016, 38(6): 795.
12. 蘭鵬, 杜辰偉, 陳培莉, 等. 微合金鋼連鑄表面橫裂紋形成機理與控制技術研究現狀[J]. 鋼鐵研究學報, 2017, 29(1): 1.
13. 蘭鵬,張家泉. 430不鏽鋼凝固顯微組織模擬的3D CAFE模型[J]. 北京科技大學學報,2014, 36(3): 315.
14. 蘭鵬,張家泉. 微觀組織參數及工藝條件對430不鏽鋼凝固顯微結構的影響[J]. 北京科技大學學報,2014, 36(4): 446.
15. 蘭鵬,張家泉. 鋼錠模用灰口鑄鐵服役工況下組織與力學行為研究[J]. 機械工程學報, 2014, 50(2):116.
16. 蘭鵬,張家泉. 灰口鑄鐵低頻熱疲勞載荷下的微觀組織與拉伸性能[J]. 材料熱處理學報, 2014, 34(4):149.[1]